How To Cut Vinyl Siding For Ledger Board

September 28, 2021 Post a Comment

Use a sharp razor knife and a straight edge as a guide to score cut the vinyl and after several passes gradually cut through. I use a straight guide like a paint stir-stick 18 ruler or even a yard-stick with a couple of rubber bands on the ends to make it non-slip to make straight cuts.

How To Install A Ledger Board On Vinyl Siding Board Poster

Apr 25 2017 - Learn how to cut and remove aluminum vinyl wood and cement board siding for installing a deck ledger board to a house wall.

How to cut vinyl siding for ledger board. Set the blade depth so you wont cut into the house sheathing below the siding. Start by making an outline on the siding where you want to position the ledger board. Then cut away the siding.

You can buy shorter sheets or larger sheets but in this example well stick with the dimensions given. Wood or concrete siding will have to. Step 2 - Cut Away the Vinyl Siding.

Cut away the marked area of siding with tin snips. Click to see full answer. If you cut out your siding to install a ledger board careful steps must be taken to ensure that moisture cannot reach your house.

The bottom part of the ledger is resting on The vinyl siding starter strip. Measure the length and width of your deck to attach the ledger correctly. Infiltrating rainwater can travel downward sideways and even upward so special flashings must be used.

Watch the blade carefully as youre cutting to make sure its staying on the line. You can then trim the pieces to be reinstalled with a J channel after the deck is completed for a clean finished look. Make the outline large enough to include space for the deck boards on top the ledger and any trim boards on the sides.

You want to avoid cutting up the house wrap beneath if possible. Measure the distance from the undersill trim to the locking tab of the siding below. Use a crayon to pre-mark the cut.

Then slip flashing behind the siding covering the top edge of the ledger. How to build a deck. What is the preferred method when attaching to a house with Vinyl siding.

Installing Deck Ledger on Vinyl Siding - YouTube. Install the ledger overtop of the siding or remove the siding attach the ledger and recase around it. Then cut away the siding.

Locate the rim joist and mark an outline on the siding where you want to position the ledger board using a tape measure pencil and chalk line. Install the ledger overtop of the siding or remove the siding attach the ledger and recase around it. If playback doesnt begin shortly try restarting your device.

Ive used it for cutting for a ledger make sure you get some appropriate J to dress up the cut just bond it on with caulk and to terminate porch railing into the siding. Installing Deck Ledger on Vinyl Siding. Step 1 determine the size of the ledger board.

Slip the flashing under. Push the saw along the line at a steady rate to get a clean smooth cut. Use your free hand to hold the vinyl siding down so it doesnt shift while youre cutting it.

If playback doesnt begin shortly try. In the past metal flashing and extra layers of roofing felt tar paper were often used but nowadays vinyl Z flashing and rolls of vinyl back flashing. Carefully cut away the siding with a utility knife braced along the edge of the carpenters square to avoid slicing through the house wrap.

Drip caps direct water away from the house keeping it from getting behind the ledger board. Set the blade depth so you wont cut. Can you put a ledger board over siding.

Make the outline large enough to include space for the deck boards on top the ledger and any trim boards on the sides. Nail undersill trim J-channel will also work over the bottom cut using 11-gauge aluminum nails. In order to install the ledger board you usually need to remove the houses siding.

Never install a ledger board over the top of siding no matter what you hear this can weaken the connection. Cut along the line you drew using the circular saw. Step 3 - Add 2 x 8 Planks Between Joists.

For instance if you are using it to protect a deck from children throwing rocks and pencils at it then you would go with a thicker vinyl so that it can withstand minor wear and tear. Its a tight fit to drive the nails into the undersill but you can gently pull back the siding. Place the piece of siding horizontally under the bottom edge of the window.

Start by making an outline on the siding where you want to position the ledger board. Attaching a deck ledger board to a vinyl-sided house requires a few extra trim pieces to keep water from leaking behind the siding. This is used to determine the depth of the notch.

Removed the siding and I have the ledger resting on what I believe is the vinyl Starter strip. Start by making an outline on the siding where you want to position the ledger board. Attaching the ledger board - YouTube.

Lol Does The vinyl Starter Strip need to be removed. How do I attach a ledger board to a house with vinyl siding. Nail undersill trim j channel will also work over the bottom cut using 11 gauge aluminum nails.

I cut the siding off and had about 12-1 left. Mark it at inch past the edge of each side of the window. Cut a length of metal drip cap flashing to the same length as the Z flashing.

Slip flashing under siding Snap a chalk line cut out the siding and tack up the ledger board. The type of vinyl siding you would use on deck ledger board depends on how much protection your ledger needs. Once you are sure about the joist location mark out the cutaway areas outer shape using a soft pencil or marker and a straight edge.

Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location. Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location. Pics of Ledger board and vinyl.

Tips On Removing Vinyl Siding For Attaching Ledger Board Contractor Talk Professional Construction And Remodeling Forum

Ledger Board Diy Home Improvement Forum

Deck Ledgers Best Practices Manual Hammer Hand Pacific Nw Builder Building A Deck Diy Deck Deck Design

Removing The Siding For The Ledger Board Decks Com

How To Attach Ledger Board To Under Roof Siding Home Improvement Stack Exchange

Ledger Board Diy Home Improvement Forum

Pin On Green Life

Attaching Ledger To Siding Tigerwood Decking

What Should I Do On The Sides Of A Deck Ledger Home Improvement Stack Exchange

Onward Hardware Is The Leading Distributor Of Builder S Hardware And Related Products Specializing In Comme Building A Deck Diy Deck Pergola Attached To House